diff --git a/ucm2/PinePhonePro/HiFi.conf b/ucm2/PinePhonePro/HiFi.conf new file mode 100644 index 0000000..3a125a9 --- /dev/null +++ b/ucm2/PinePhonePro/HiFi.conf @@ -0,0 +1,278 @@ +SectionVerb { + EnableSequence [ + # First of all, disable the internal speaker amplifier + cset "name='Internal Speaker Switch' off" + + ### Based on /codecs/rt5640/EnableSeq.conf ### + + # RT5640 default output routing + cset "name='DAC MIXL INF1 Switch' on" + cset "name='DAC MIXR INF1 Switch' on" + cset "name='DAC MIXL Stereo ADC Switch' off" + cset "name='DAC MIXR Stereo ADC Switch' off" + cset "name='Stereo DAC MIXL DAC L1 Switch' on" + cset "name='Stereo DAC MIXR DAC R1 Switch' on" + cset "name='Stereo DAC MIXL DAC L2 Switch' on" + cset "name='Stereo DAC MIXR DAC R2 Switch' on" + cset "name='OUT MIXL DAC L1 Switch' on" + cset "name='OUT MIXR DAC R1 Switch' on" + cset "name='SPK MIXL DAC L1 Switch' on" + cset "name='SPK MIXR DAC R1 Switch' on" + + # uncomment to enable swap between AIF1 and AIF2 + # warning: can only work with SSP0 firmware enabled + cset "name='SDI select' 0" + cset "name='DAI select' 0" + #cset "name='SDI select' 1" + #cset "name='DAI select' 1" + + cset "name='DAC2 Playback Switch' on" + + # Input Configuration + cset "name='Stereo ADC1 Mux' ADC" + cset "name='Stereo ADC2 Mux' DMIC1" + cset "name='ADC Capture Switch' on" + + cset "name='Mono ADC L1 Mux' ADCL" + cset "name='Mono ADC R1 Mux' ADCR" + cset "name='Mono ADC L2 Mux' DMIC L1" + cset "name='Mono ADC R2 Mux' DMIC R1" + cset "name='Mono ADC Capture Switch' on" + + # Set capture volume to 0dB so modem audio doesn't overdrive the ADC + cset "name='ADC Capture Volume' 47" + cset "name='Mono ADC Capture Volume' 47" + + # The second 'Mono ADC' path does not have a 'Boost Gain', + # set this to 0dB so that the volume of the AIF1 and AIF2 paths is equal. + cset "name='ADC Boost Gain' 0" + + # Set IN1 internal mic boost to 8 (max) + # Set IN2 headset-mic boost to 1, headset mics are quite loud + # Set IN3 (modem audio) boost to 0 as it's already loud enough + cset "name='IN1 Boost' 8" + cset "name='IN2 Boost' 1" + cset "name='IN3 Boost' 0" + + # Start with all controls which are used by the individual + # input/output Enable/DisableSequences off + + cset "name='RECMIXL BST1 Switch' off" + cset "name='RECMIXR BST1 Switch' off" + # IN2 is headset mic, make sure its route is enabled + cset "name='RECMIXL BST2 Switch' on" + cset "name='RECMIXR BST2 Switch' on" + cset "name='RECMIXL BST3 Switch' off" + cset "name='RECMIXR BST3 Switch' off" + + cset "name='Stereo ADC MIXL ADC1 Switch' off" + cset "name='Stereo ADC MIXR ADC1 Switch' off" + cset "name='Stereo ADC MIXL ADC2 Switch' off" + cset "name='Stereo ADC MIXR ADC2 Switch' off" + cset "name='Mono ADC MIXL ADC1 Switch' off" + cset "name='Mono ADC MIXR ADC1 Switch' off" + cset "name='Mono ADC MIXL ADC2 Switch' off" + cset "name='Mono ADC MIXR ADC2 Switch' off" + + # Limit amplification factor of earpiece amplifier so sound stays clear + cset "name='Class D SPK Ratio Control' 1.66x" + + # Turn off playback switches by default, otherwise both Speaker + # and headphones are playing audio initially until headphones are + # re-inserted. + cset "name='HP L Playback Switch' off" + cset "name='HP R Playback Switch' off" + cset "name='Speaker L Playback Switch' off" + cset "name='Speaker R Playback Switch' off" + + # MONO output is used as IN3 here, so make sure it's disabled + cset "name='Mono Playback Switch' off" + + # Set playback volumes to 0dB + cset "name='HP Playback Volume' 31" + cset "name='Speaker Playback Volume' 31" + ] + + DisableSequence [ + # Turn off all output channels + cset "name='HP L Playback Switch' off" + cset "name='HP R Playback Switch' off" + cset "name='HP Channel Switch' off" + cset "name='HPO MIX HPVOL Switch' off" + cset "name='Speaker L Playback Switch' off" + cset "name='Speaker R Playback Switch' off" + cset "name='Speaker Channel Switch' off" + cset "name='SPOL MIX SPKVOL L Switch' off" + cset "name='SPOL MIX SPKVOL R Switch' off" + + + # Reset output routing + cset "name='DAC MIXL INF1 Switch' off" + cset "name='DAC MIXR INF1 Switch' off" + cset "name='OUT MIXL DAC L1 Switch' off" + cset "name='OUT MIXR DAC R1 Switch' off" + cset "name='SPK MIXL DAC L1 Switch' off" + cset "name='SPK MIXR DAC R1 Switch' off" + ] + + Value { + TQ "HiFi" + } +} + +SectionDevice."Earpiece" { + Comment "Internal Earpiece" + + ConflictingDevice [ + "Headphones" + "Speaker" + ] + + EnableSequence [ + cset "name='SPOL MIX SPKVOL L Switch' on" +# for mono speaker we apply left on right +# cset "name='SPOR MIX SPKVOL R Switch' on" + cset "name='SPOL MIX SPKVOL R Switch' on" + cset "name='Speaker Channel Switch' on" + cset "name='Speaker L Playback Switch' on" + cset "name='Speaker R Playback Switch' on" + ] + + DisableSequence [ + cset "name='Speaker Channel Switch' off" + cset "name='Speaker L Playback Switch' off" + cset "name='Speaker R Playback Switch' off" + ] + + Value { + PlaybackPriority 100 + PlaybackPCM "hw:${CardId}" + PlaybackMixerElem "Speaker" + PlaybackVolume "Speaker Playback Volume" + PlaybackMasterElem "DAC1" + } +} + +SectionDevice."Speaker" { + Comment "Internal Speaker" + + ConflictingDevice [ + "Earpiece" + "Headphones" + ] + + EnableSequence [ + cset "name='HPO MIX HPVOL Switch' on" + cset "name='HP Channel Switch' on" + cset "name='HP L Playback Switch' on" + cset "name='HP R Playback Switch' on" + cset "name='Internal Speaker Switch' on" + ] + + DisableSequence [ + cset "name='Internal Speaker Switch' off" + cset "name='HP Channel Switch' off" + cset "name='HP L Playback Switch' off" + cset "name='HP R Playback Switch' off" + ] + + Value { + PlaybackPriority 200 + PlaybackPCM "hw:${CardId}" + PlaybackMixerElem "HP" + PlaybackVolume "HP Playback Volume" + PlaybackMasterElem "DAC1" + } +} + +SectionDevice."Headphones" { + Comment "Headphones" + + ConflictingDevice [ + "Earpiece" + "Speaker" + ] + + EnableSequence [ + cset "name='HPO MIX HPVOL Switch' on" + cset "name='HP Channel Switch' on" + cset "name='HP L Playback Switch' on" + cset "name='HP R Playback Switch' on" + ] + + DisableSequence [ + cset "name='HP Channel Switch' off" + cset "name='HP L Playback Switch' off" + cset "name='HP R Playback Switch' off" + ] + + Value { + PlaybackPriority 300 + PlaybackPCM "hw:${CardId}" + JackControl "Headphones Jack" + PlaybackMixerElem "HP" + PlaybackVolume "HP Playback Volume" + PlaybackMasterElem "DAC1" + } +} + +SectionDevice."Mic" { + Comment "Internal Microphone" + + ConflictingDevice [ + "Headset" + ] + + EnableSequence [ + cset "name='Mono ADC MIXL ADC2 Switch' on" + cset "name='Mono ADC MIXR ADC2 Switch' on" + cset "name='Stereo ADC MIXL ADC2 Switch' on" + cset "name='Stereo ADC MIXR ADC2 Switch' on" + ] + + DisableSequence [ + cset "name='Mono ADC MIXL ADC2 Switch' off" + cset "name='Mono ADC MIXR ADC2 Switch' off" + cset "name='Stereo ADC MIXL ADC2 Switch' off" + cset "name='Stereo ADC MIXR ADC2 Switch' off" + ] + + Value { + CapturePriority 100 + CapturePCM "hw:${CardId}" + CaptureMixerElem "ADC" + CaptureVolume "ADC Capture Volume" + CaptureSwitch "ADC Capture Switch" + } +} + +SectionDevice."Headset" { + Comment "Headset Microphone" + + ConflictingDevice [ + "Mic" + ] + + EnableSequence [ + cset "name='Mono ADC MIXL ADC1 Switch' on" + cset "name='Mono ADC MIXR ADC1 Switch' on" + cset "name='Stereo ADC MIXL ADC1 Switch' on" + cset "name='Stereo ADC MIXR ADC1 Switch' on" + ] + + DisableSequence [ + cset "name='Mono ADC MIXL ADC1 Switch' off" + cset "name='Mono ADC MIXR ADC1 Switch' off" + cset "name='Stereo ADC MIXL ADC1 Switch' off" + cset "name='Stereo ADC MIXR ADC1 Switch' off" + ] + + Value { + CapturePriority 200 + CapturePCM "hw:${CardId}" + JackControl "Headphones Jack" + CaptureMixerElem "ADC" + CaptureVolume "ADC Capture Volume" + CaptureSwitch "ADC Capture Switch" + } +} diff --git a/ucm2/PinePhonePro/PINE64-PinePhonePro-.conf b/ucm2/PinePhonePro/PINE64-PinePhonePro-.conf new file mode 100644 index 0000000..c333958 --- /dev/null +++ b/ucm2/PinePhonePro/PINE64-PinePhonePro-.conf @@ -0,0 +1,16 @@ +Syntax 4 +Comment "PinePhone Pro" + +SectionUseCase."HiFi" { + File "/PinePhonePro/HiFi.conf" + Comment "Default" +} + +SectionUseCase."Voice Call" { + File "/PinePhonePro/VoiceCall.conf" + Comment "Phone call" +} + +Include.card-init.File "/lib/card-init.conf" +Include.ctl-remap.File "/lib/ctl-remap.conf" +Include.codec-init.File "/codecs/rt5640/init.conf" diff --git a/ucm2/PinePhonePro/VoiceCall.conf b/ucm2/PinePhonePro/VoiceCall.conf new file mode 100644 index 0000000..aaaa4ef --- /dev/null +++ b/ucm2/PinePhonePro/VoiceCall.conf @@ -0,0 +1,275 @@ +SectionVerb { + EnableSequence [ + # First of all, disable the internal speaker amplifier + cset "name='Internal Speaker Switch' off" + + ### Based on /codecs/rt5640/EnableSeq.conf ### + + # Get audio only from the microphones, not the system + cset "name='DAC MIXL INF1 Switch' off" + cset "name='DAC MIXR INF1 Switch' off" + cset "name='DAC MIXL Stereo ADC Switch' on" + cset "name='DAC MIXR Stereo ADC Switch' on" + cset "name='Stereo DAC MIXL DAC L1 Switch' on" + cset "name='Stereo DAC MIXR DAC R1 Switch' on" + cset "name='Stereo DAC MIXL DAC L2 Switch' on" + cset "name='Stereo DAC MIXR DAC R2 Switch' on" + cset "name='OUT MIXL DAC L1 Switch' off" + cset "name='OUT MIXR DAC R1 Switch' off" + cset "name='SPK MIXL DAC L1 Switch' off" + cset "name='SPK MIXR DAC R1 Switch' off" + + # uncomment to enable swap between AIF1 and AIF2 + # warning: can only work with SSP0 firmware enabled + cset "name='SDI select' 0" + cset "name='DAI select' 0" + #cset "name='SDI select' 1" + #cset "name='DAI select' 1" + + cset "name='DAC2 Playback Switch' on" + + # Input Configuration + cset "name='Stereo ADC1 Mux' ADC" + cset "name='Stereo ADC2 Mux' DMIC1" + cset "name='ADC Capture Switch' on" + + cset "name='Mono ADC L1 Mux' ADCL" + cset "name='Mono ADC R1 Mux' ADCR" + cset "name='Mono ADC L2 Mux' DMIC L1" + cset "name='Mono ADC R2 Mux' DMIC R1" + cset "name='Mono ADC Capture Switch' on" + + # Set capture volume to 0dB so modem audio doesn't overdrive the ADC + cset "name='ADC Capture Volume' 160" + cset "name='Mono ADC Capture Volume' 160" + + # The second 'Mono ADC' path does not have a 'Boost Gain', + # set this to 0dB so that the volume of the AIF1 and AIF2 paths is equal. + cset "name='ADC Boost Gain' 0" + + # Set IN1 internal mic boost to 8 (max) + # Set IN2 headset-mic boost to 1, headset mics are quite loud + # Set IN3 (modem audio) boost to 0 as it's already loud enough + cset "name='IN1 Boost' 8" + cset "name='IN2 Boost' 1" + cset "name='IN3 Boost' 0" + + # Start with all controls which are used by the individual + # input/output Enable/DisableSequences off + + cset "name='RECMIXL BST1 Switch' off" + cset "name='RECMIXR BST1 Switch' off" + # IN2 is headset mic, make sure its routed to the left channel + cset "name='RECMIXL BST2 Switch' on" + cset "name='RECMIXR BST2 Switch' off" + # IN3 is modem audio, route it to the right channel + cset "name='RECMIXL BST3 Switch' off" + cset "name='RECMIXR BST3 Switch' on" + + cset "name='Stereo ADC MIXL ADC1 Switch' off" + cset "name='Stereo ADC MIXR ADC1 Switch' off" + cset "name='Stereo ADC MIXL ADC2 Switch' off" + cset "name='Stereo ADC MIXR ADC2 Switch' off" + cset "name='Mono ADC MIXL ADC1 Switch' off" + cset "name='Mono ADC MIXR ADC1 Switch' off" + cset "name='Mono ADC MIXL ADC2 Switch' off" + cset "name='Mono ADC MIXR ADC2 Switch' off" + + # Limit amplification factor of earpiece amplifier so sound stays clear + cset "name='Class D SPK Ratio Control' 1.66x" + + # Loopback IN3 to earpiece/speaker/headphones + cset "name='OUT MIXR REC MIXR Switch' on" + cset "name='SPK MIXR OUT MIXR Switch' on" + + # Send the left channel (microphones) to the modem through DAC L1 + cset "name='LOUT MIX DAC L1 Switch' on" + # Don't use DAC R1 nor the OUTVOL blocks as we use them for + # routing audio from the modem + cset "name='LOUT MIX DAC R1 Switch' off" + cset "name='LOUT MIX OUTVOL L Switch' off" + cset "name='LOUT MIX OUTVOL R Switch' off" + + # Disable left channel for HP (speaker/headphones) output + # as we're only routing modem audio to the right channel + cset "name='HP L Playback Switch' off" + + # Turn off playback switches by default, otherwise both Speaker + # and headphones are playing audio initially until headphones are + # re-inserted. + cset "name='HP L Playback Switch' off" + cset "name='HP R Playback Switch' off" + cset "name='Speaker L Playback Switch' off" + cset "name='Speaker R Playback Switch' off" + + # MONO output is used as IN3 here, so make sure it's disabled + cset "name='Mono Playback Switch' off" + + # Set playback volumes to 0dB + cset "name='HP Playback Volume' 31" + cset "name='Speaker Playback Volume' 31" + ] + + DisableSequence [ + # Turn off all output channels + cset "name='HP L Playback Switch' off" + cset "name='HP R Playback Switch' off" + cset "name='HP Channel Switch' off" + cset "name='Speaker L Playback Switch' off" + cset "name='Speaker R Playback Switch' off" + cset "name='Speaker Channel Switch' off" + + # Reset output routing + cset "name='DAC MIXL Stereo ADC Switch' off" + cset "name='DAC MIXR Stereo ADC Switch' off" + cset "name='OUT MIXR REC MIXR Switch' off" + cset "name='SPK MIXR OUT MIXR Switch' off" + cset "name='LOUT MIX DAC L1 Switch' off" + + # Reset ADC input routing + cset "name='RECMIXL BST2 Switch' off" + cset "name='RECMIXR BST3 Switch' off" + ] + + Value { + TQ "VoiceCall" + } +} + +SectionDevice."Earpiece" { + Comment "Internal Earpiece" + + ConflictingDevice [ + "Headphones" + "Speaker" + ] + + EnableSequence [ + cset "name='SPOL MIX SPKVOL L Switch' on" + # Send right channel to left as it's mono only + cset "name='SPOL MIX SPKVOL R Switch' on" + cset "name='Speaker Channel Switch' on" + cset "name='Speaker L Playback Switch' on" + ] + + DisableSequence [ + cset "name='Speaker Channel Switch' off" + cset "name='Speaker L Playback Switch' off" + ] + + Value { + PlaybackPriority 200 + PlaybackPCM "hw:${CardId}" + PlaybackMixerElem "Speaker" + PlaybackVolume "Speaker Playback Volume" + PlaybackMasterElem "DAC1" + } +} + +SectionDevice."Speaker" { + Comment "Internal Speaker" + + ConflictingDevice [ + "Earpiece" + "Headphones" + ] + + EnableSequence [ + cset "name='HPO MIX HPVOL Switch' on" + cset "name='HP Channel Switch' on" + cset "name='HP R Playback Switch' on" + cset "name='Internal Speaker Switch' on" + ] + + DisableSequence [ + cset "name='Internal Speaker Switch' off" + cset "name='HP Channel Switch' off" + cset "name='HP R Playback Switch' off" + ] + + Value { + PlaybackPriority 100 + PlaybackPCM "hw:${CardId}" + PlaybackMixerElem "HP" + PlaybackVolume "HP Playback Volume" + PlaybackMasterElem "DAC1" + } +} + +SectionDevice."Headphones" { + Comment "Headphones" + + ConflictingDevice [ + "Earpiece" + "Speaker" + ] + + EnableSequence [ + cset "name='HPO MIX HPVOL Switch' on" + cset "name='HP Channel Switch' on" + cset "name='HP R Playback Switch' on" + ] + + DisableSequence [ + cset "name='HP Channel Switch' off" + cset "name='HP R Playback Switch' off" + ] + + Value { + PlaybackPriority 300 + PlaybackPCM "hw:${CardId}" + JackControl "Headphones Jack" + PlaybackMixerElem "HP" + PlaybackVolume "HP Playback Volume" + PlaybackMasterElem "DAC1" + } +} + +SectionDevice."Mic" { + Comment "Internal Microphone" + + ConflictingDevice [ + "Headset" + ] + + EnableSequence [ + cset "name='Stereo ADC MIXL ADC2 Switch' on" + ] + + DisableSequence [ + cset "name='Stereo ADC MIXL ADC2 Switch' off" + ] + + Value { + CapturePriority 100 + CapturePCM "hw:${CardId}" + CaptureMixerElem "ADC" + CaptureVolume "ADC Capture Volume" + CaptureSwitch "ADC Capture Switch" + } +} + +SectionDevice."Headset" { + Comment "Headset Microphone" + + ConflictingDevice [ + "Mic" + ] + + EnableSequence [ + cset "name='Stereo ADC MIXL ADC1 Switch' on" + ] + + DisableSequence [ + cset "name='Stereo ADC MIXL ADC1 Switch' off" + ] + + Value { + CapturePriority 200 + CapturePCM "hw:${CardId}" + JackControl "Headphones Jack" + CaptureMixerElem "ADC" + CaptureVolume "ADC Capture Volume" + CaptureSwitch "ADC Capture Switch" + } +} diff --git a/ucm2/conf.d/simple-card/PINE64-PinePhonePro-.conf b/ucm2/conf.d/simple-card/PINE64-PinePhonePro-.conf new file mode 120000 index 0000000..93c4ff1 --- /dev/null +++ b/ucm2/conf.d/simple-card/PINE64-PinePhonePro-.conf @@ -0,0 +1 @@ +../../PinePhonePro/PINE64-PinePhonePro-.conf \ No newline at end of file